Bodyfillers

Multi Putty 1K NC Multi Putty 200g multifunctional lightweight putty. 25% lighter than standard putties. Very easy application and easy sanding, with no sandpaper clogging. Working time: 3-5mins Drying time: 16-30min Sanding: P120-320

Easy Sand 2K Flowable Filler 1Litre. Finish Line Liquid Glaze is a flowable polyester filler putty for finishing, blending and skim coating bodywork, pinholes, grind marks, low spots, and other surface imperfections. This putty adheres well to steel, galvanized, other zinc coated steel, aluminium, and most rigid to semi-rigid fiberglass and thermo-set plastics. Has a higher resin content than traditional fillers which makes it less porous. This ensures lower moisture penetration and lower absorption of primer. Process time is therefore faster & a non-shrinkage finish is ensured. Drying time: 2.5-3h at 20 degrees Celsius Drying time: 15-20min at 60 degrees Celsius Film thickness: 40-180μm Normal coats: 1-2

Fibre DIY 2K Fibreglass Repair Kit 250g - Fast curing Polyester Repair Kit for the repair of rust holes and GRP components. Kit includes hardener and glass-fibre-mat. Quick-drying polyester resin filters the mat and glass cloth excellently. Easy application. Contains additives which cause the reduction of styrene emissions during and after application, as well as an additive which causes the hardened laminate not to have a sticky surface after drying, which is particularly important when machining with abrasive materials. Excellent adhesion to steel surfaces. For car body repairs, construction and home DIY.

Multi Putty Universal Plastic Putty 500g multifunctional lightweight putty. 25% lighter than standard putties. Very easy application and easy sanding, with no sandpaper clogging.

Glass Fibre Reinforced Putty 1.8Kg for all deep filling and bridging works. Excellent sanding properties. Can be used on all applications. Working time: 3-5mins Drying time: 16-30min Sanding: P120-320

Multi-Fill Multifunctional Putty 1.8Kg combines the deep filling properties of a fill-putty with the high surface quality of a finishing putty. Due to its excellent density, it has very good shaping properties. It can also be used as a finishing putty, leaving a smooth surface without pores. Excellent sanding properties. Working time: 3-5mins Drying time: 16-30min Sanding: P120-320

Multi Master Service Line Polyfill 2K premium lightweight, easy-sand body filler 3 Litre.

Spray-fill 2K Polyester Sprayable Grey Body Filler 3.7 Litre - Excellent adhesion on various substrates including GRP, Metal, Wood, Polyester Laminates and Hard Plastic. Excellent flow and filling properties enabling it to be applied over large areas Filling both small and deeper imperfections (pinholes and sanding marks) easily. Anti-corrosive and very easy sanding. Drying time: 15-20min at 20 degrees Celsius Film thickness: 30μm Normal coats: 2 Recoat after: 20min Sanding after: 3h

Beetroot Board - Multi-layered mixing board supplied with 100 disposable sheets. For body filler, pastes etc.

Finish Line Plastic Spreaders with a bevelled edge used to mix body fillers, pastes etc.

Metal Body Filler Spatula Set of four in different sizes. For mixing body fillers, pastes etc. Japan Style. Supplied in plastic bag.

Sealplast Brushable Sealer is a single-component product used in car refinishing to seal all joints in the bodywork, boots, and wheel arches. It is easy to apply and provides a durable and flexible seal. This sealer is designed to prevent moisture, dirt, and other contaminants from entering the vehicle through gaps in the bodywork. It is commonly used by car manufacturers and body shops for its effectiveness in preventing corrosion and rust.

UNIPLAST hot stapler, is the fastest and most efficient solution for repairing plastics. It can repair and reinforce any piece of plastic such as bumpers, instrument panels, headlight supports etc. UNIPLAST is a small and easy to use device. Its configuration is very simple, an on/off button to start the device and an option for the temperature you want to heat the staple to. UNIPLAST has three different positions. Low temperature (L) for 1.5mm plastic thickness. Medium temperature (M) for 2mm plastic thickness. High temperature (H) suitable for more than 2mm plastic thicknesses. UNIPLAST provides you with an excellent repairing level and incredible savings in time and money.